Schlachtschiff HMS Hood / Halinski / 1:250 [FERTIG]

  • Hi All


    Left putting the pictures here until I thought I could overcome the fit problems on this ship (bought on Ebay and apparently the early version).I made a bit of a mess of the hull to start with but I think I have covered most of that up. Nothing is actually glued together properly as yet, gives me a chance to alter it some more if necessary. Scaling the ship down lessened the problems as I expected to have to cut and stick in some odd places. Now it begins to look like Hood I am happier.



    gruss


    Ich hatte mich den Bildern hier zurückgehalten, bis ich die Paßprobleme bei diesem Modell überarbeitet hatte. Ich habe das Modell von eBay und es ist anscheinend die frühe Version. Ich habe etwas Probleme mit dem Rumpf gehabt, aber jetzt habe ich wohl alles behoben. Bis jetzt ist noch nichts wirklich zusammengeklebt, damit ich immer noch anpassen kann.
    Die Verkleinerung von 1:200 auf 1:250 hat die Probleme etwas verringert, ich mußte nicht soviel rumschnippeln, wie ich eigentlich erwartet hatte. Jetzt sieht es schon etwas nach Hood aus und ich bin glücklicher.

  • Hi All


    I got a bit fed up modifying Hood and moaning about so I decided to make my own mess and try designing a ship myself and anyway Hood needed an escort.


    Tribal class fleet destroyer HMS Eskimo 1/250 circa 1938 as L75 I did not quite get the bow plates right hence the gap at the top. Rob sent me some more detailed plans which shows the errors on my guesses at the deck houses but a tin paper overlay should fix that.


    Ipicked this type as it was a fairly simple design without too much deck clutter.


    Hopefully the next redraw will see it somewhere near right.


    :usenglish:
    Hallo zusammen,


    Ich hatte ein bisschen die Nase voll vom modifizieren der Hood und der Jammerei darüber. Also habe ich mich entschlossen ein eigenes Schiff zu entwerfen, weil die Hood eh eine Eskorte brauchte.


    Zerstörer HMS Eskimo 1/250, Baujahr 1938 als L75. Ich habe die Bugplatten noch nicht ganz richtig hinbekommen, daher der Spalt am oberen Rand. Rob hat mir detailliertere Pläne zugesendet, die einige falsche Annahmen von mir bei den Decksaufbauten zeigen. Aber das ist mit etwas Alufolie hinzubekommen.
    Ich habe diesen Schiffstyp gewählt, weil es ein einfaches Design mit wenig Decksaufbauten ist.
    Hoffentlich bekomme ich es mit der nächsten Zeichnung noch etwas besser hin.



  • Hallo Barry,
    Jetzt verstehe ich warum hast du damals nach Baupläne und Fotomaterial über "Eskimo" gesucht.
    Ich bin sehr gespannt auf weitere Fotos.
    Mit den besten Grüßen mein Freund
    Christoph


    Now I understand why you have asked for plans and fotos on the "Eskimo".


    I am looking forward to new fotos. With best regards my friend.

  • Hi Friends


    This is still not worth a section in it's own right as I am still learning as I go along, the trouble is if I use the mouse too much my fingers will not roll cardboard so forgive the rough building. The decks have all been overlaid several times so the edges are lifting. I need to design a 4 barrel pompom next also the gun is borrowed from HMS Savage to check for fit and will need to be a one piece barrel. The Vickers 4.7 " gun has an overhead rammer which will cover any detail on the gun breeches so it will be a lot simpler.


    Hopefully I will sort out which photo program works the best for me and then if anyone is interested I will try to put a theme together. I've had a great deal of help from Rob and Maurice over on cardmodels.net and not least the plans from Narod.ru


    A couple of photographs before I start rebuild 2.


    gruss

  • Hi Friends


    Finally finished the main guns and stuck a few more bits down and the sun was shining so the camera worked more or less.


    I bought Siatki ($45 US) from Gremir models yesterday for designing deck houses for ships or buildings or railway trucks etc it is extremely simple to use and produces instant results bit like having a "just in time" factory order.


    It is well worth downloading the the free trial.


    regards

  • Hallo Barry,


    Sieht super aus! Unglaublich wie du das Modell trotz viele Fehlern gebaut hast (Ich weiß dass diesen Baubogen von Halinski den Du verwendest hast sind sehr Fehlerhaft) Mein Riesen Respekt!
    Mit den besten Grüßen
    Christoph

    Looks super. Unbelievable how you built this model despite the many problems (i know the Halinski model you use has a lot of mistakes). My greatest respect!

  • Witam


    Bardzo podoba mi sie twoja praca jak i rowniez model. Na tym forum jestem od niedawna i z racji tego nie sledzilem tej relacji, dlatego odnosze wrazenie ze model w wersji ukonczonej wyglada jakby byl to calkiem inny model niz ten ktory prezentowany jest wyzej.
    (zapewne sie myle)


    Model wyszedl Ci naprawde rewelacyjnie (skrome zdanie uczacego sie modelarza)


    pozdrawiam Kamil


    Hallo,


    Deine Arbeit so wie das Modell gefällt mir sehr. Seit kurzer Zeit bin ich auf diesem Forum Mitglied, deshalb habe ich nicht den ganzen Baubericht von Anfang an befolgt. Ich habe der Eindruck dass Dein fertigen Modell sieht ganz anders wie das Modell den Du am Anfang präsentiert hast (sicherlich irre mich)
    Das Modell hast du wirklich super gebaut (das ist bescheidene Meinung von Modellbauer der noch viel lernen muss)
    Gruß
    Kamil

  • Hallo Blaszka


    Hier in diesen Bauberichten Barry zeigen zwei Schiffe:
    Zerstörer Eskimo und Schlachtschiff HMS. Hood
    Aber keiner ist noch fertig. Den Bau geht weiter.


    Gruß
    Scorpio


    Czesc Blaszka
    Tu w tej relacji Barry presentuje dwa okrety :
    Niszczyciel Eskimo i panzernik HMS Hood
    I zaden z nich nie jest jeszcze gotowy . Budowa trwa nadal.
    Pozdrawiam
    Scorpio

  • Hi Friends


    The kindest critic would describe this as "rough as a bears a**e" and having tried all the bits I think it's time to apply what I have learned getting this far (further than I expected). Then rebuild it with more care.


    My apologies for confusing everybody which theme this is.


    Time to finish off Hood


    If anyone has any pictures of a Tribal class destroyers deck fittings I would be grateful to have them. Thank you.


    gruss


    Hallo Freunde,


    die freundlichste Kritik würde dies als "Grob wie ein Bärena***" beschreiben. Jetzt wo ich so weit gekommen bin (weiter als ich gedacht habe), wäre es an der Zeit meine Erfahrungen zu sammeln und es sorgfältiger neu zu bauen.


    Meine Entschuldigung an alle, die ich mit diesem zweiten Modell verwirrt habe, worum es in diesem Thread geht. Jetzt ist es Zeit, die Hood fertig zu bauen.


    Falls jemand noch irgendwelche Bilder der Decksausrüstung von Tribal-Class Zertörern hat, wäre ich dankbar, diese zu bekommen. Danke.

  • only A gun is the final representation I am trying to make the fold lines external in the next attempt.

    Nur die vorderste Kanone zeigt das endgültige Ergebnis. Beim nächsten Versuch werde ich die Faltmarken ausserhalb der Bauteile anlegen.

  • Hello barry,


    your Shipbuilding of te HOOD is gread congartulatons.


    greetings
    Ernst

  • Hi Friends


    Vent details around "B" turret.


    Question


    If anyone has built this ship are the vents around A turret just tightly rolled paper tubes or are painted headed pins better please


    gruss


    Lüfter, rund um Turm "B".


    Frage: Falls jemand dieses Schiff schon gebaut hat: Sind für die Lüfter rund um Turm A eng gerollte Papier-Rollen besser - oder nehme ich lieber angemalte Stecknadeln mit Köpfen?

  • Hallo Barry,
    Du kannst natürlich alles verwenden:
    Papier, wenn Du Papierpurist bist oder Stecknadeln (Nur das finde ich nicht so Gut auf Grund der Kugelförmige Kopf) oder so wie ich das mache sehe Bild (das alles bemale ich mit entsprechende Farbe)


    Hello Barry,
    You can use everything of course:
    Paper, if you are a paper-purist or pins, I don't find only that property on reason the spherical head so, or just like I that does I see picture, that paints everything, with corresponding color,

    With the best greetings
    Christoph

  • Hi


    I was not in the mood to cut a lot of wire gun pieces so I added the ships boats at least they make the deck look more interesting.


    gruss

    Ich war nicht in der Stimmung eine Menge Kanonenrohre aus Draht zu schneiden, also habe ich die Beiboote angebracht. Die lassen das Deck interessanter aussehen...

  • Hi All


    I got a good tip from CRS on cardmodels he suggested using a piece of plastic tube cut from an old ball point pen to the length of the gun barrels. It worked extremely well I stuck it vertically on to a piece of scrap card, pushed the wire down and snipped it off at the right length, the added bonus is it stops the shrapnel flying round the room. Having my usual trouble making cardbord steps I seem to need something with an edge like a Samurai sword. I made the bollards out of electric wire insulation, my fingers are getting too stiff these days.


    gruss

    Von CRS habe ich auf cardmodels.net einen guten Tipp zur Herstellung von Kanonenrohren aus Draht bekommen. Man schneidet ein Stück einer leeren Kugelschreibermine auf passende Länge und stellt diese senkrecht auf eine Unterlage. Wenn man dann den Draht reinsteckt, kann man ihn prima auf der richtigen Länge abschneiden. Und es verhindert auch, dass die Drahtstücke wie Schrapnell durch den Raum fliegen. Ich habe wieder meine üblichen Probleme, Leitern aus Karton zu bauen - ich glaube ich brauche eine Klinge wie ein Samurai-Schwert...


    Die Poller mache ich aus Isolierung, meine Finger sind etwas steif im Moment...

  • Hi All


    Nearing the end of the slow job of fixing the ship's rails it would have been a lot easier if I had thought to bore the stanchion holes before assembly of the pieces. There are 250 seperate stanchions to fix I used used PVA glue mostly but used UHU Superglue gel to fix the "king posts" to get the tension on the cotton.


    I made the initial holes with a lancet needle and then used a round headed pin, I held the thin decks with a flat pair of tweezers to avoid bending the edges


    gruss

  • Hi Friends


    On the last part of Hood now the rigging and a few odd bits I am searching through all the cut up pages for.


    Just in case I drop the soldering iron onto the decks while doing the rigging I have put some ridiculously large pictures on the net so you have a choice.


    Eskimo is in some of the pictures mainly because I want (one day) to do a seascape of her bunkeroing off Hood, even though it would be enourmous plus Hood had a couple of Tribals as a screen.


    http://homepage.ntlworld.com/ccompro/hood/PIC_0138.jpg


    http://homepage.ntlworld.com/ccompro/hood/PIC_0139.jpg


    http://homepage.ntlworld.com/ccompro/hood/PIC_0141.jpg


    http://homepage.ntlworld.com/ccompro/hood/PIC_0142.jpg


    gruss

  • Hi Friends


    The rigging using the wire from computer flat cables was not a great success it is very difficult to pull it straight (nearly impossible) but having glued it into the decks with superglue I was stuck with it, hopefully it might sag under it's own weight. The spars were too thin too take any tension which did not help. I guess I will have to learn how to pull plastic. One more uploader gun for the front turret and some paint and hopefully then it will be finished. She is a bit battered in places due to my problems in handling this size model and the time it took to build. If I stand well back it does not seem so bad.


    If anyone has any suggestions for rigging I would be gratefull.


    gruss

  • Hello barry.


    Me big Respect for your Work Congratalutons.


    best regards
    Ernst

  • hallo barry


    you have build a very good model of the HOOD. i know it`s very hard to build a war ship. =D> =D> =D> =D> =D>


    much greetings


    guido