Hi All!
No words. Only photo.
Krupp Protze Kfz.70 /1:25/ Modelik 1/06 [FERTIG]
-
- Completed
- Hogges
-
-
Looking forward to see your build of this truck!!
So bring on the shots -
Oooo! this is one cool model! :super:
good luck! -
oh well, i really like this truck. i'll be watching your build with special interest.
-
Many thanks to You for support!
I found some mistakes - length of the protector is incorrect. -
I use clear water and brush. After moisture inside each protector I am carefully extend all ot them. Before cutting I highly recommend paint to dark color internal side of the protector. In this model I don't want paint all wheels. I paint only white ends.
-
Too many boards with white edges inside and outside of the basket. Basket almost ready. Barrel is ready. I am cut off strape for glue and make it round. Many time was spent to hide white spaces... =(
You must be careful about thickness. W.Richard show right thickness of the detail but this is mean total thicknessl!!! For example author say - "glue XXX detail (printed on the 200g/m2 paper with real thickness 0.2mm) to 1mm cardboard". Attention! You must glue this detail to the 0.8mm cardborad!!! If You need fold this detail and glue cardboard inside - cardboard must be 0.5mm!!! And so on. -
hy hogges!
no words, only =D> =D> =D> =D> =D> =D>
best regards from cologne, robert
-
Thank You Robert for the good words!!!
Four barrels are ready. Doors in the basket has just a bit bigger. -
Looking really good Serge!!
I have this model on my next order from Modelik -
Thank You, Johnny!
Thickness and thickness again.
Yesterday I am finished all wheels. Axles has wrong diameter 3.5mm. It must be 3.0mm... I am advicing look at drafts. Drafts is really good in M1:1. You can check thickness of all parts of the wheels. For nuts imitation I use laser cutted 0.8mm nuts from Draf Model colored with acrylic paint. -
I was too busy on this week...
steering wheel was made from copper wires (1.5mm and 0.5mm diameter) and solder and paint.
Mainspings on the back torsion are made from steel wire 0.9mm. I think it look better then paper cylinder with black stripes,isn't it? -
Thats just amazing Serge!!
Those parts look as real as it gets!! -
Thank You, Johnny!
Today i am ready to show next portion of Protze...
Too many small pieces - speed making is dramatically reduced...Pipes was made from copper wires 2mm diameter.
windshield wiper is combined from original with thin stripe cutted from 0.5mm (black in massive) cardboard. -
Wow!!
I just love those tiny details!!
-
hi !
Your truck is really impressive ,especially suspension details ans stering wheel are ravishing.I`ll here regular visit.
Reagards from Gdansk Piter -
Thank You, guys!
:prost: -
"Sorry for the delay, Generals!
I am gathering my forces..." (c) Zero Hour -
On photos I show almost all parts what must be glued...
"The end is near!" (c) Pumba
-
Great job @).Your model looks outstanding :meister:
-
Quote
Originally posted by Hogges
On photos I show almost all parts what must be glued..."The end is near!" (c) Pumba
Wonderful looking model!!!!!!! Great photos showing off the construction.
Cheers...
-
Thank You very much for nice words! @) @) @)
Welcome to the gallery! :prost:
-
Amazing building Serge!
clean and nice!
congratulations on finishing the model! :prost: -
Thank you All for the godd words!
Thank You Snake7 AKA Igor! =)
-
Administrator
Added the Label Completed -
René Pinos
Moved the thread from forum wbb.board.VEHICLES_FIN to forum Construction Reports.